Search
Log in
Login:
Password:
Register
Forgot your password?

AMM-3320 LCR Meter

Digital LCR meter. Dual LCD display +analog bar. Measurements: Capacitance 200pF...200mF, Inductance 200µH...20kH, Resistance 20Ω...200MΩ, quality factor, dissipation factor, phase angle, resistance. DCR. Frequency: 100Hz, 120Hz, 1kHz, 10kHz, 100kHz. Measurement in parallel mode (Lp, Cp, Rp) and series mode (Ls, Cs, ESR). Relative measurements and data hold. Mini-USB interface.


Manuals: 
The LCR meter AKTAKOM AMM-3320 is designed to measure Inductance (L), Capacitance (C), and Resistance (R). Mini USB port allows connecting the LCR meter to PC.

Features

  • 1,999 counts dual LCD display
  • Analog Bar display
  • Mini USB port connect to PC
  • Auto LCR smart check and measurement
  • Parameters Ls, Lp, Cs, Cp, DCR, ESR, D, Q and θ
  • Basic accuracy: 0.3% with resolution of 0.01%
  • Measurement frequency up to 100 kHz
  • Sorting function
  • Relative measurement
  • Data hold
  • Backlight, full angle for LCD display
  • 4-terminal measurement configuration
  • Automatic power off
  • Battery and external power supply
  • Battery voltage indication

Parameter

Primary DCR: DC resistance
Ls/Cs series inductance / capacitance
Lp/Cp parallel inductance / capacitance
Secondary θ: phase angle
D: dissipation factor
ESR: equivalent series resistance
Q: quality factor
Rp: equivalenent parallel resistance

Specifications


Frequency Range
L 100/120Hz 20mH…20kH
1kHz 2000μH…2000H
10kHz 200μH…20H
100 kHz 20μH…200mH
C 100/120Hz 20nF…20mF
1kHz 2000pF…2mF
10kHz 200pF…200μF
100kHz 200pF…20μF
R 100/120Hz 200Ω…200MΩ
1kHz 20Ω…200MΩ
10kHz 20Ω…20MΩ
100kHz 20Ω…2MΩ

L DCR 200…200M
D/Q 0.001…1999
θ 0.00°…±180°

Impendance accuracy

The bellow-listed accuraies are guaranteed by the meter with normal use under the operating temperature of 18-28 and relative humidity less than 80%.


0.1-1Ω 1-10Ω 10Ω-100kΩ 100kΩ-1MΩ 1M-20MΩ 20M-200 MΩ Remark
DCR 1.0%+5d 0.5%+3d 0.3%+2d 0.5%+3d 1.0%+5d 2.0%+5d D<0.1
100/120 Hz 1.0%+5d 0.5%+3d 0.3%+2d 0.5%+3d 1.0%+5d 2.0%+5d
1 kHz 1.0%+5d 0.5%+3d 0.3%+2d 0.5%+3d 1.0%+5d 5.0%+5d
10 kHz 1.0%+5d 0.5%+3d 0.3%+2d 0.5%+3d 1.0%+5d N/A
100 kHz 2.0%+5d 1.0%+5d 0.5%+3d 1.0%+5d 2.0%+5d (1M-2MΩ)
  • Frequency: 100/120/1k/10k/100kHz
  • Display: Dual display + analog bar display
  • Test level: 0.6Vrms
  • Rang mode: Auto and Hold
  • Equivalent Circuit: Parallel and Series
  • Calibration function: Open/Short
  • Interface: Mini-USB
  • Measurement speed: approx. 1.2 times/second
  • Measurement terminal: 4-terminal
  • Basic accuracy: 0.3%
  • Power: AAA*6 battery or external power supply
  • Auto power off: 5 min (with batteries)
  • Operation environment: temperature (0…40°C), humidity (90%RH, 40°C, no condensation)
  • Storage temperature: -25°C…50°C
  • Size: 8×4×2in/ 203.2×101.6× 50.8mm
  • Weight: 20oz/567g

Accessories

  • LCR testing leads (pair)

  • LCR clips (open and short)

  • Black crocodile lead (single)

  • USB - mini cable

  • Batteries

  • Soft bag

  • User manual

Capacitance measurement

  • Turn on the power.
  • If exists voltage in the capacity, connect the two ends of the capacitor for a short time to discharge.
  • There are two ways for capacitance input:
    a. Insert the positive polarity of capacitance into the positive terminal and its negative polarity into the negative terminal;
    b. Insert the black and red testing lines with alligator clip into the "LCUR", "LPOT" terminal and "HCUR", "HPOT" terminal respectively. Connect the alligator clips to the two ends of capacitance corresponding to its polarity.
  • The default test mode is Auto LCR mode, the capacitance value will show on primary display and the dissipation factor D will show on secondary display. In Auto LCR mode, the D/Q/ESR key, SEL/PAL key, SORTING key and REL% key are not available.
  • Press FUNC. key twice to select Auto-C mode. The primary LCD display will show the capacitance value. The secondary LCD display will show the dissipation factor D. The quality factor Q, equivalent resistance ESR/Rp or phase angle θ can also be shown by pressing the D/Q/ESR key.
  • Press FREQ key to select frequency value: 100/120/1k/10k/100kHz.
  • Press SER/PAL key to select series or parallel mode.
Note: 1. When Auto-LCR mode is active, the secondary parameter will show the equivalent resistance in parallel mode (Rp) to replace the D factor if the C measured value is less than 5pF.
2. In order to avoid damaging the instrument, the capacitance requires discharge before measuring.

Capacitance measurement

Inductance measurement

  • Turn on the power.
  • There are two ways for inductance input:
    a. Insert the measured inductance into the input terminal directly;
    b. Connect the alligator clips to the ends of the measured inductance.
  • The default test mode is Auto LCR mode, the inductance value will show on primary display and the quality factor Q will show on secondary display. In Auto LCR mode, the D/Q/ESR key, SEL/PAL key, SORTING key and REL% key are not available.
  • Press FUNC. key to select Auto-L mode. The primary LCD display will show the inductance value. The secondary LCD display will show the quality factor Q. The equivalent resistance ESR/Rp, phase angle Θ or dissipation factor D can also be shown by pressing the D/Q/ESR key.
  • Press FREQ key to select frequency value: 100/120/1k/10k/100kHz.
  • Press SER/PAL key to select series or parallel mode.

Resistance measurement

  • Turn on the power.
  • There are two ways for resistance input:
    a. Insert the measured resistance into the input terminal directly;
    b. Connect the alligator clips to the ends of the measured resistance.
  • The default test mode is Auto LCR mode, the resistance value will show on primary display and the phase angle θ will show on secondary display. In Auto LCR mode, the D/Q/ESR key, SEL/PAL key, SORTING key and REL% key are not available.
  • Press FUNC. key three times to select Auto-R (ACR) mode. The primary LCD display will show the resistance value. The secondary parameter is omitted and the D/Q/ESR key is not available.
  • Press FREQ key to select frequency value: 100/120/1k/10k/100kHz.
  • Press SER/PAL key to select series or parallel mode.
  • Press FUNC. key four times to select DCR mode. The primary LCD display will show the resistance value. The secondary parameter is omitted and the D/Q/ESR key, SEL/PAL key and FREQ key are not available.
Note: The phase angle Θ will show on secondary display only in Auto-LCR mode. During Auto-R mode or DCR mode, the secondary parameter is not available.

Frequently Asked Questions

  • What is the purpose of AutoLCR mode in AKTAKOM AMM-3320 RLC Meter?
  • How to select the secondary measured parameter when operating AKTAKOM AMM-3320 RLC Meter?
  • How to select the primary measured parameter when operating AKTAKOM AMM-3320 RLC Meter?

  • What is the purpose of AutoLCR mode in AKTAKOM AMM-3320 RLC Meter?

    AutoLCR mode is used in AKTAKOM AMM-3320 RLC meter for automatic selection of the primary and secondary parameters for L, C, R modes and it is activated on default. Selection is made in accordance with the test result. This function makes it convenient to take measurements of different-type or unknown elements.

    Condition Primary parameter Secondary parameter
    lθl<-11° Capacity (C) Dissipation factor (D) (if C<5pF the secondary parameter is Rp)
    lθl>11° Inductance (L) Quality factor (Q)
    lθl<11° Resistance (R) Phase angle (θ)


    Up

    How to select the secondary measured parameter when operating AKTAKOM AMM-3320 RLC Meter?

    In order to select the secondary parameter when operating AKTAKOM AMM-3320 RLC Meter you need to press “D/Q/ESR” button. Each time you press the button the parameter changes in the following order: D (dissipation factor) ► Q (quality factor) ► θ (phase angle) ► ESR (equivalent series resistance)


    Up

    How to select the primary measured parameter when operating AKTAKOM AMM-3320 RLC Meter?

    In order to select the primary parameter when operating AKTAKOM AMM-3320 RLC Meter you need to press “FUNC” button. Each time you press "FUNC" the parameter changes in the following order: AUTO LCR (automatic selection of the value under measurement) ► L-Q (measurement of inductance and quality factor) ►C-D (measurement of capacity and dissipation factor) ►R (resistance measurement) ►DCR (DC resistance measurement).

    L/C/R values can be positive and negative. If in C-D mode the primary parameter has "-" sign then the element should be measured in inductance mode. If in L-Q mode the primary parameter has "-" sign then the element should be measured in capacity mode. If in R mode the primary parameter is negative then this means calibration error and it is necessary to re-calibrate AMM-3320 RLC meter.


    Up


    Back to the section
    AKTAKOM - the Best in Test Award Winner!