Search
Log in
Login:
Password:
Register
Forgot your password?

ACM-2352 Clamp Meter

AKTAKOM ACM-2352 Professional True RMS 1500A AC Watt Clamp Meter provides accurate Watt, AC Current and Voltage readings regardless of waveforms.

Manuals: 
User's Manual (382.2 Kb)

AKTAKOM ACM-2352 Professional True RMS 1500A AC Watt Clamp Meter provides accurate Watt, AC Current and Voltage readings regardless of waveforms.

Features

  • True RMS Value (Voltage and Current)
  • 4 digits with dual display LCD
  • MIN/MAX measurement
  • True power / apparent power / power factor measurement
  • Data Hold
  • Auto Ranging
  • Overflow Indication

Specifications

Function Range Max Resolution Accuracy
AC Voltage 100V 0.01V ±(1.2%+5d)
750V 0.1V
1000V 1V
AC Current
40A
0.01A
±(2.0%+5d)
400A 0.1A
1500A 1A
Active Power
900kW 0.01kW ±(3.0%+5d)
Apparent Power 900kVA 0.01kVA ±(3.0%+5d)
Reactive Power 900kVAR 0.01kVAR ±(4.0%+5d)
Power Factor (Capacitive or Inductive) 0.3...1 0.1
±(0.02%+2d)
Phase Angle 0°...90° 1° ±2°
Frequency 40Hz...40MHz 1Hz ±(0.5%+5)
Energy 1...9999kWh
1kWh ±(3%+2)

General Specification

  • LCD: 4 digits, dual
  • Auto Power Off: 30 minutes
  • Manual Data Memory and Read: 99 sets
  • Jaw opening: 2.16" (55mm)
  • Size: 23.4×4×1.8in/295×100×46mm
  • Weight: 19oz/537g
ACM-2352 Clamp Meter - rear view
ACM-2352 Clamp Meter - rear view
Enlarge
ACM-2352 Clamp Meter - inputs
ACM-2352 Clamp Meter - inputs
Enlarge
ACM-2352 Clamp Meter - controls
ACM-2352 Clamp Meter - controls
Enlarge
ACM-2352 Clamp Meter - noncontact voltage sensor
ACM-2352 Clamp Meter - noncontact voltage sensor
Enlarge
ACM-2352 Clamp Meter - full set
ACM-2352 Clamp Meter - full set
Enlarge

AC/DC measurement with AKTAKOM ACM-2352 clamp meter

Note: Disconnect the test leads before measuring with the clamp meter.

  1. Rotate the function switch to 1500AAC/DC position.
  2. Press MODE button to select AC or DC.
  3. Press the trigger to open jaw. Fully enclose only one conductor.
  4. Read the current value in the display.
  5. If the value is less than 400A rotate the function switch to 400AAC/DC position to improve resolution.

DCA Zero
Zero feature removes offset values and improves accuracy for DC measurement. Therefore select ADC and press ZERO button (there should be no conductor in the clamp). The display will show zero. The offset value will be stored and removed from all measurements.

Frequency
When ACV is selected, the measured frequency can be viewed in the lower display.


AC/DC voltage measurement with AKTAKOM ACM-2352 clamp meter

Note: the maximum value of the input signal for DC and AC voltage measurement should not exceed the acceptable value specified in the user manual. Do not attempt to measure voltage exceeding these limits. Failure to follow these instructions can result in electric shock and the instrument damage.

  1. Rotate the function switch to V position.
  2. Press MODE button to select AC or DC Voltage.
  3. Insert the black test lead banana plug into the negative COM jack. Insert the red test lead banana plug into the positive V jack.
  4. Touch the black test probe tip to the negative side of the circuit. Touch the red test probe tip to the positive side of the circuit.
  5. Read the voltage value in the display.

Frequency
When ACA is selected the measured frequency can be viewed in the lower display.


Resistance measurement with AKTAKOM ACM-2352 clamp meter

Note: Remove power from the device under test before measuring resistance.

  1. Set the function switch to Ω position.
  2. Insert the black test lead banana plug into the negative COM jack. Insert the red test lead banana plug into the positive V jack.
  3. Touch the black test probe tip to one side of the device to be measured. Touch the red test probe tip to the other side of the device to be measured.
  4. Read the resistance value in the display.

Continuity test with AKTAKOM ACM-2352 clamp meter

  1. Connect as described for resistance measurements.
  2. Press the MODE button to select continuity .
  3. Touch the test probe tips across the circuit or component under test.
  4. If the resistance is <50Ω, a tone will sound.

Diode test with AKTAKOM ACM-2352 clamp meter

  1. Connect as described for resistance measurements
  2. Press MODE button to select diode test 
  3. Touch the test probe tips to the diode or semiconductor junction under test. Note the meter reading.

Reverse the test lead polarity by reversing the red and black leads.

Note: If one reading displays a value (typically 0.400V to 01.800V) and the other one displays OL, the diode is good. If both readings display OL the device is open. If both readings are very small or “0”, the device is shorted.

Capacitance measurement with AKTAKOM ACM-2352 clamp meter

Note: To avoid electric shock discharge the capacitor before measuring.

  1. Press MODE button to select capacitance measurements.
  2. Insert the black test lead banana plug into the negative COM jack. Insert the red test lead banana plug into the positive jack .
  3. Touch the black test probe tip to one side of the device. Touch the red test probe tip to the other side of the device.
  4. Read the capacitance value in the display.

For very large values of capacitance measurement time can be several seconds before the final reading stabilizes.

Note: Zero feature removes stray test lead capacitance to improve the accuracy of low value capacitance measurement. Therefore press and hold MODE ZERO button for two beeps. The display will show zero. The offset value is now stored and is removed from all measurements.

Frequently Asked Questions

  • Can max. and min. values be fixed when operating AKTAKOM ACM-2352 clamp meter?
  • How does non-contact voltage detector work in AKTAKOM ACM-2352 clamp meter?

    • Can max. and min. values be fixed when operating AKTAKOM ACM-2352 clamp meter?

    Yes, you may fix max. and min. values following the below step:

    1. Press MAX/MIN button to activate MAX/MIN recording mode. The display icon "MAX" will appear. ACM-2352 will start recording and displaying the measured maximum value.
    2. Press MAX/MIN button again and “MIN” will appear on the display. ACM-2352 will display the measured minimum value during the recording session.
    3. Press MAX/MIN button and “MAX MIN” will appear. The clamp meter will display the present reading but will continue to update and store the max and min readings.
    4. To exit MAX/MIN mode press and hold the MAX/MIN button for about 2 seconds.


    Up

    How does non-contact voltage detector work in AKTAKOM ACM-2352 clamp meter?

    To use the non-contact voltage detector of AKTAKOM ACM-2352 clamp meter do the following:

    1. Before the use always test the Voltage Detector on a known live circuit to verify proper operation.
    2. Rotate the function switch to any measurement position.
    3. Place the detector probe tip on the conductor to be tested.
    4. If AC voltage is present, the NCV detector will turn on with a steady red light.

    Note: The conductors in electrical cord sets are often twisted. For best results move the probe tip along a length of the cord to assure placing the tip close to the live conductor.



    Up


    Back to the section
    Login  •  Contact Us  •  Privacy Policy  •  Terms of Use  •  Site Map

    © AKTAKOM, 2009-2024